The pump is the first line of defense that drains water out of the basement. They also protect your foundation and the structural integrity of your home.
In the early spring, when there is a lot of snow melting, or when there is heavy rain in the summer, you need it most. It will be called more, so you should check the operation before it is too late. It may have been running for a while when you called the pump. Therefore, you need to plan ahead and make sure your pump is running when you need it, and don't let you go back to the flooded basement.
The maintenance of the oil pan pump will not take more than 10 minutes. You need to check the operation of the pump and ensure that it is always available when you need it.
Pump maintenance tips
Cover the pool basin.
• This will stop animals and children and make sure you don't have any debris falling into the basin.
from
• The lid also reduces odor and evaporation
Check the debris
Check the sink/pool for any debris and remove it before operating the pump. We don't want this to go into the pump inlet or even block the pump. Therefore, be sure to remove debris before testing the pump.
Check pump screen / entry screen
Check that the inlet screen on the pump is free of debris and residue buildup as if they were blocked, which will reduce the efficiency of the sewage pump. Therefore, this will reduce the amount of pump removal, which will greatly reduce the pump instead of its design. If necessary, bring a hose and flush the outside of the sewage pump and the sink to remove any debris that may affect the pump's operation.
Electricity and safety
Since there is electricity and water in the same unit, make sure to use the Ground Fault Indicator [GFI] to electrically protect the electrical. This should guarantee your safety, because if there is a fault, you should trip the power. If you have a test facility, check this out.
Cable routing
Check that the cable routing is correct and that the cable is intact. Make sure the cable is as far from water as possible. Also check that the cable is secure and not loose, and that the cable is likely to fall into the sump. This can be fatal and has happened in some rare cases. So check that the cable is secure and secure.
Check the discharge pipe
A check valve is always installed to prevent the pumped water in the discharge pumping line from returning to the oil sump and refilling the oil sump after pumping. It only allows the water to move in one direction, which is of course outside your puddle. If this is a problem, you will see your tank refilled and your pump will run more often.
Inspect the drain line for leaks or damage. Make sure all parts are intact, including the end of the pumping pipe. If you can visually see the pumping line, make sure the end is free to run properly for pumping water.
Pump test your pump
Fill the oil sump very slowly with water and observe the operation of the oil pump. In this way, you can observe the operation of the float switch, making sure it moves with ease and freely.
Check the operation of the float switch
Once the float is added to the switch point, you must observe the pump operation. Of course you should also listen to the pump. In this case, you are listening to the connection of the float switch and the switch to connect and operate the pump correctly without any hesitation or resistance. Since the float switch is considered to be one of the weaknesses of the pump, you can observe this in this test and make sure your switch is working properly. If the switch is intermittent or does not function properly, you can replace the switch without having to purchase a replacement pump.
Listening to the pump
Now the pump is running and you want to hear the pump itself running. Make sure there are no screams or wear and noise on the metal or even metal. There should be some slight vibration when the pump is running. If there is excessive vibration, you must investigate it. Excessive vibration or noise may indicate that the pump's bearings or internal work may be worn. In this case, if you need to change the pump in a hurry, it is best to install a replacement pump nearby.
Operating the pump multiple times
This is done several times in order to operate the pump efficiently and to check that the pump stops pumping when the pump level drops to the appropriate level and the switch returns to the rest position. In general, what you are doing is checking the complete cycle of the pump to check if it is working properly because it may need it.
Check valve operation
The click of the check valve is also heard in this sequence of operations; when the pump stops pumping, you want to hear the operation of the check valve. The check valve should be closed with a click and prevent water from returning to the oil sump.
Maintenance pump and pump installation points
from
• Cover the sink cover.
from
• Check the debris
from
• Check pump screen / inlet screen
from
• Electricity and safety
from
• Cable routing
from
• Check the discharge pipe
from
• Water test the pump
from
• Check the operation of the float switch
from
• Listen to the pump
from
• Operate the pump multiple times
from
• Check valve operation
from
• Replace all covers and parts
Once you are satisfied with the operation of the pump and have checked everything, you need to make sure that all parts and covers are replaced in the correct position of the pump. You should also check your sewage pump regularly to make sure it is always at your service.
Orignal From: Pump maintenance tips
No comments:
Post a Comment